Last Updated on March 23, 2023 by Robinellis
22
There are a few ways to resize .22 rifle brass. The most common way is to use a full-length resizing die.
This die will push the shoulder of the brass back and make the case smaller so that it can be used again. another way is to use a neck sizing die. This die will only resize the neck of the brass and not the shoulder.
This is good for when you want to keep your cases in good condition for a long time.
- Get a can of WD-40 and a small brush
- Open the can of WD-40 and generously apply it to the brass that you want to enlarge
- Use the small brush to work the WD-40 into all the crevices of the brass
- Let the brass sit for at least 30 minutes so that the WD-40 can penetrate deep into the metal
- After 30 minutes have passed, use a pair of pliers to grab hold of the brass and give it a good twist
- The twisting motion will cause the brass to expand slightly and increase in size
Credit: www.youtube.com
Why Do You Bump the Shoulder Back on Brass?
There are a few reasons why you might want to bump the shoulder back on brass. First, it can help to improve the accuracy of your shots. Bumping the shoulder back helps to align the bore of the gun with the target, which can lead to more accurate shots.
Additionally, this technique can help to prevent jams and misfires. By bumping the shoulder back, you ensure that all of the brass is properly seated in the chamber before firing. Finally, this method can also help to prolong the life of your gun by preventing wear and tear on the internal parts.
Should I Neck Size My Brass?
If you’re a reloader, at some point you’ve probably wondered whether or not you should neck size your brass. Neck sizing is the process of resizing only the neck of the brass case so that it will fit snugly around the bullet. This is in contrast to full length sizing, which resize the entire length of the brass case.
There are pros and cons to both neck sizing and full length sizing, and ultimately it’s up to the reloader to decide which method is best for their needs. Here’s a quick rundown of the pros and cons of each method:
Neck Sizing Pros:
– Less work – since you’re only resizing the neck of the brass case, it takes less time than full length sizing.
– More accurate – since you’re not resizing the entire length of the brass case, there’s less chance for inaccuracies. The dimensions of your chamber are more likely to match those of your bullet, resulting in better accuracy.
– Preserves cases – since you’re not resizing as much material, your cases will last longer before they need to be replaced.
Neck Sizing Cons:
– Can cause feeding problems – if your cases are too snug around the bullet, they can get stuck in the chamber when trying to feed them into your firearm.
This can be especially problematic with semiautomatic firearms.
– Requires a bushing die – most dies don’t come with a bushing die (the die that does the actual neck sizing), so you’ll need to purchase one separately if you want to go this route.
Full Length Sizing Pros:
– Ensures proper fit – since you’re resizing the entire length of the brass case, you can be sure that it will fit properly in any firearm chamber regardless of manufacturer tolerances.
– Easy on equipment – unlike neck sizing which requires a bushing die, full length sizing only uses one standard die (assuming you already have one).
Full Length Sizing Cons: More work – Full Length Sizing usually takes more time than just Neck Resize because obviously there is more area being worked on per piece.
.
What is the Best Tool for Measuring Shoulder Bump?
There is no definitive answer to this question as the best tool for measuring shoulder bump will vary depending on the specific requirements of the person carrying out the measurement. However, some common tools that can be used for this purpose include a tape measure, ruler or caliper. Whichever tool is used, it is important to ensure that it is placed correctly on the shoulder in order to obtain an accurate reading.
Can You Shoulder Bump With a Full Length Die?
The answer is no, you cannot shoulder bump with a full length die. The reason for this is because the die would not be able to make contact with your shoulder due to its size. Additionally, even if you could make contact, the force required to dislodge the die from your shoulder would be significantly greater than what is needed to simply drop it from waist height.
Extend Your Brass Life, How to Shoulder Bump – Reloading : EP 10
Conclusion
223
This blog post covers the topic of how to resize .223 brass for reloading. The author provides clear instructions and illustrations to help the reader understand the process.
This is a helpful post for anyone who wants to learn how to resize their own rifle brass.