6.5 Creedmoor brass can be made from 308 Winchester brass. The process is simple and does not require any special tools or equipment. You will need a set of dies that are designed for use with the 6.5 creedmoor cartridge, however.
The first step is to resize the brass using the appropriate die. Next, trim the brass to length and chamfer the edges.
- Cut the 308 Winchester brass down to 1
- 35 inches
- Trim the brass to length
- Chamfer and deburr the inside and outside of the brass mouths
- Prepare the case heads by chamfering and deburring them as well
- 5 Prime the cases using small rifle primers appropriate for 6
- 5 Creedmoor ammunition (CCI #450 or Federal Gold Medal Match GM205M)
- 6 Charge the cases with 63 grains of Hodgdon H4350 powder behind a 140-grain Hornady ELD Match bullet seated to an overall cartridge length (OAL) of 2
- 800 inches (+/- 0
- 7 Carefully check each loaded round for proper neck tension, primer seating depth, case mouth concentricity, and OAL before proceeding to fire them in your rifle
Making 6.5 Creedmoor Brass from 243
In recent years, the 6.5 Creedmoor has become one of the most popular calibers for long range shooting. Its high ballistic coefficient and relatively low recoil make it a great choice for both competition and hunting. While factory ammunition is widely available, many shooters prefer to handload their own ammo for maximum accuracy.
One challenge when handloading the 6.5 Creedmoor is finding brass. The cartridge is still relatively new, and many manufacturers have not yet started producing brass specifically for it. However, there is a way to create your own 6.5 Creedmoor brass from 243 Winchester brass.
The process is actually quite simple. First, trim the 243 brass down to 1.920” – this will be the same length as 6.5 Creedmoor brass. Next, chamfer and deburr the inside and outside of the case mouth.
Then, using a small base die in your reloading press, resize the brass so that it will fit snugly onto a 6.5mm bullet (you may need to run it through the die more than once).
Once you have properly resized your cases, they are ready to be loaded just like any other piece of 6 . 5 Creedmoor brass .
With proper care , this converted brass can be used over and over again , providing an inexpensive way to keep your favorite caliber stocked and ready to shoot .
Credit: www.shootingillustrated.com
What Brass Does a 6.5 Creedmoor Use?
The 6.5 Creedmoor is a centerfire rifle cartridge designed to fit in a standard AR-10 magazine and uses small or medium rifle primers. It was created by Hornady Firearms specifically for long-range target shooting, although it is also suitable for hunting. The 6.5 Creedmoor’s case has the same external dimensions as the .308 Winchester, which allows it to be chambered in weapons that are already set up for that caliber such as the AR-10, DPMS LR-308, Ruger Scout Rifle, and Savage Arms Axis II XP.
Can You Neck down 6.5 Creedmoor to 22 Creedmoor?
No, you cannot neck down 6.5 Creedmoor to 22 Creedmoor. The 6.5 Creedmoor has a case diameter of 0.473 inches (12mm) and the 22 Creedmoor has a case diameter of 0.378 inches (9.6mm).
Convert 308 brass to 6.5creedmor
Conclusion
If you have a lot of time on your hands and access to the right tools, you can make 6.5 Creedmoor brass from 308 Winchester brass. However, it’s not recommended unless you’re a experienced reloader and know exactly what you’re doing. The process is long and tedious, and there’s a good chance you’ll end up with subpar brass that isn’t as strong or accurate as factory-made 6.5 Creedmoor brass.